Quick Reference
Guide
This page is a quick reference
guide to help you set up your VAAR 2000. Please read your
manual for an in-depth explanation of the features and setup
options of the VAAR 2000
VCR
Codes Click
on this link.
System
Status
|
Status
LED
|
Function
|
Details
|
|
ORANGE
BLINKING
|
POWER UP DELAY
|
10 seconds
|
|
ORANGE
|
DISARMED
|
|
|
ORANGE / GREEN
BLINKING
|
ARMING DELAY
|
60 seconds
|
|
GREEN
|
ARMED
|
|
|
RED BRIGHT / DIM
BLINKING
|
VCR RECORDING
|
120 seconds from last
triggered event
|
|
RED BLINKING
|
VCR FINISHED RECORDING -
ARMED
|
|
|
RED / ORANGE
BLINKING
|
VCR FINISHED RECORDING -
DISARMED
|
Press momentary switch or
ARM then DISARM the VAAR 2000 to set to ORANGE
|
Quick
Setup
- Unpack contents of VAAR 2000
and take back cover off
- Connect 9V battery to VAAR
2000 (L3 On if battery is Rechargeable : L3 OFF if
battery is not rechargeable)
- Connect the Plugpack into J1
(Note white trace wire is positive)
- Connect VCR to same mains
power outlet (with jumper L5 "ON") - Preferably connect
both to a Interruptible Power Supply
- Check to see if VCR goes into
standby when first powered up ( If so jumper L4 must be
"ON")
- Put a blank Cassette tape into
your VCR
- Find The Programming code for
your video (see reverse side of this sheet)
- Slide the "prog" switch
ON
- Enter 4 Digit code ( 1 digit
at a time - slide appropriate digit switch ON then OFF
for each of the 4 digits)
- slide the "prog" switch
OFF
- slide the "Test" switch ON
then OFF with the VAAR 2000 pointed directly at the
VCR
- Check to see the VCR starts
Recording (IF not try the code again or a different Code
if there is more than 1 choice)
- Once the VCR starts recording
turn the Mains power OFF to both the VCR & VAAR
2000
- Turn the mains power back ON
to both again (at same time)
- Check that the VAAR 2000 takes
the video out of standby (if L4 is ON)
- Connect the alarm sensors or
triggering devices to J2 on VAAR 2000 (+12V or +9V on J6
may be used to power sensors etc..)
- **REMOVE LINK ACROSS NC ON J2
SENSOR INPUT IF SENSOR USES THE NC INPUT
- Connect external arming device
to J8 if used e.g Standalone keypad , key barrel switch -
(between KEY &COM)
- **REMOVE THE LINK ON J8 IF
EXTERNAL LATCHED SWITCH USED
- Connect external Power Monitor
device if used to J7 (Note NC and NO are given in the
power OFF state)
- Connect external Status Led to
J9 if used (Cathode of LED's must be connected to 0V from
J6)
- Connect Camera and or "Time
Date Generator" to VCR (+12V or +9V on J6 may be used to
power camera if needed)
- Once The system is set up arm
the system and wait for the green LED to come ON , check
that the sensor output triggers the VAAR 2000 (RED LED
bright then dim flashing) and that the VCR starts
recording with a Picture - A T.V or Monitor may be
connected to VCR for this trial .
- Remember that the VCR and VAAR
2000 should be kept in a Safe and secure area hidden from
sight with the VAAR 2000 pointing at the VCR or
reflecting off a mirrored surface.
You need help:
please call us on +
614 04 052 007
|
